user?s manual 2L415B high performance-cost ratio 2-phase microstepping driver ver 2.0 appreciate your selection of motionking tm driver. to make full use of its versatile performance, please read this manual carefully before using the driver! motionking(china) motor industry co., ltd. t: (86)519-8988 6261 f: (86)519-8515 1172 web site: www.motionking.com e-mail: sales@motionking.com the content in this manual has been carefully prepared and is believed to be accurate, but no responsibility is assumed for inaccuracies. motionking reserves the right to revise the manual without prior not ice for reliability, function and design improvement. motionking doe s not assume any liability arising out of the application or use of any product or circ uit described herein; neither does it convey any license under its patent rights of others. motionking?s general policy does not recommend the use of its products in life support or aircraft applications wherein a failure or malf unction of the product may directly threaten life or injury. according to motionking?s sale s terms, the user of motionking products in life support or aircraft applications assume s all risks of such use and indemnifies motionking against all damages. ? 2007 by motionking motor industry co., ltd.. all rights reserved
2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 2 contents 1. general introduction 3 2. specifications & features 3 3. application field 3 4. definition of pin signal 4 5. specification of electric 5 6. operating environment & parameter 5 7. mechanical dimensions 6 8. power supply 6 9. selecting of microstep resolution and driver current 7 10. connection of moto r 8 11. matching between driver & motor 8 2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 3 2L415B microstepping resolution driver 1. general introduction 2L415B is a high performance microstepping reso lution driver that incorporates the most advanced technology in the worl d. it is suitable for driving any 2-phase and 4-phase hybrid step motors under 1.5a current. by usin g advanced bipolar constant-current chopping technique, it can output higher speed and more po wer than other drivers from the same motor. its resolution function makes the motors run at high accuracy, less vibration and lower noise. 2. specifications & features z high performance, low price z supply voltage +40vdc z 20khz chopping frequency z compatible of ttl input telegraph signal z current automatic half reduction statically z driving current 1.5a/phase z highest reaction frequency 100 khz z extremely small 86*55*20mm (3.386*2.165*0.787inch) z bipolar constant-current chopping z opto-isolated inputs z selectable resolution of 1, 2, 4, 8, 16, 32 & 64 z portable size suitable for set-up z microstep resolution can be changed on-the-fly z driving any 2 phase stepping motor with 4, 6, 8 winding under 1.5a current z current reverse connection protection 3. application field suitable for a wide range of automatically e quipment and facility, for instance air bonding, labeling machines, cutting machine, laser labeling, graph plotter, engraving machines, cnc and pick-place instrument etc. the function is perfect particularly in the devices expected with low noise, less vibration, high speed and more precision.
2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 4 4. definition of pin signal connector p1 configurations pin function details pul pulse signal : this input represents pulse signal, effective for each rising edge; 4-5v when pul-high, 0-0.5v when pul-low. for reliable response, pulse width should be longer than 1.5ms. series connect resistors for current-limit ing when +12v or +24v used. dir direction signal: high/low level signal, correlative to motor rotation direction. for reliable response, dir must be ahead of pul by 5ms at least. 4-5v when di r- high, 0-0.5v when dir-low. motor rotation direction also de pends upon the connection of the motor windings, exchange any motor phase can reverse motor rotation direction. opto opto-coupler power supply, and the typical voltage is +5v. ena enable signal: this signal is used for enabling/disabling drive. high level for enabling drive and low leve l for disabling driv e. usually left unconnected (enabled). 2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 5 connector p2 configurations pin function details gnd dc power ground +v dc power supply, 15~40vdc, including voltage fluctuation and emf voltage. a+, a- motor phase a b+, b- motor phase b 5. specification of electric (t j =25 ) 2L415B supply voltage +12 to 40 vdc rate supply voltage +24vdc output current peak value 0.1 to 1.5 a (adjustable) resolution precision 2 resolution (400 step/rev), 8 resolution (1600 step/rev), 16 resolution (3200 step/rev), 32 resolution (6400 step/rev), 64 resolution (12800 step/rev). 6. operating environment and parameters cooling natural cooling or forced convection place avoid dust, oil frost and corrosive gas temperature 0 ? +50 humidity 40 90%rh environment vibration 5.9m/s 2 max storage temp. -20 +65 net weight 150 g approx.
2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 6 7. mechanical dimensions 8. power supply the driver can work normally with power s upply range between dc12v to dv40v, it is better to use unregulated dc power supply, or it is workable to use transformer + bridge + filter capacitance, the capacitance can be 1100 uf or so. be reminded that the voltage peak value not exceed 40v after adjusting current, otherwise the driver will be damaged. it is recommended to use 24-36v dc power s upply, it can avoid the voltage fluctuation exceed the rate voltage range. motionking can supply the suitable dc power supply. using regulated switch power supply, please set the output current range to be the maximum. attention: 1. not to reverse the power positive and negative when connecting; 2. it is recommended to use non-stable power 3. the voltage not to exceed the max. when the electric net power supply is fluctuant. 4. when using unregulated supply, the current output rating must more than the driver setting current by 60%. using regulated power supply, must more than the driver?s setting current. 5. in order to lower the cost, two or three drivers can share the same power supply. 2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 7 9. selection microstep resolution and driver current this driver uses a 6-bit dip switch to set micr ostep resolution, dynamic current and standstill current, details as below: microstep resolution selection microstep resolution is set by sw4, sw 5, sw 6 of the dip switch as shown in the following table: microstep steps/rev.(for1.8o motor) sw4 sw5 sw6 1 200 on on on 2 400 off on on 4 800 on off on 8 1600 off off on 16 3200 on on off 32 6400 off on off 64 12800 on off off current settings peak current (a) sw1 sw2 sw3 0.21a off on on 0.42a on off on 0.63a off off on 0.84a on on off 1.05a off on off 1.26a on off off 1.50a off off off note: due to motor inductance, the actual curre nt in the coil may be smaller than the dynamic current settings, particul arly under high speed condition.
2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 8 10. connection of motor 2L415B driver can drive any 2 phrase / 4 phrase motor with 4, 6 or 8 lines under 1.5a current. phrase a of the stepping motor conne cted between 3 and 4 pins of p2, phrase b connected between 5 and 6 pins of p2. the de tailed connection of 4, 6, 8 lines stepping motor is listed as below: 11. matching between driver and motor this driver can drive any 2 phrase and 4 phrase motor under 1.5a current, in order to get the most perfect effect, must set the proper s upply voltage and current. the supply voltage determines the speed of the motor, and the curre nt determines the output torque of the motor. 2L415B 2 2 l l 4 4 1 1 5 5 b b m m i i c c r r o o s s t t e e p p p p i i n n g g d d r r i i v v e e r r v v e e r r 2 2 . . 0 0 www.motionking.com 9 1. supply voltage setup: generally speaking, when the motor runs at hi gh speed, higher voltage makes higher torque so avoid step-lost. but in the other way, hi gh voltage can lead over-voltage protect or, the driver will be damaged, furthe rmore, operate under high voltage, the low speed vibration is very large, so usually set the voltage to be dc24-36v. 2. output current setup: for the same motor, higher current means higher torque, but both the motor and diver?s radiation are seriously. so the current usually se t to be the value of tepid but not heat which occur in motor?s continuous working status. (1). 4 and 6 lines motor high speed mode: output current set to be the same, or a little bit less then the motor?s rate current; (2). 6 phase motor high torque mode: output cu rrent set to be 70% of the motor?s rate current; (3). 8 lines motor in series connection: output current set to be 70% of the motor?s rate current; (4). 8 lines motor parallel c onnection: output current set to be 140% of the motor?s rate current. note: run the motor for 15-30 minutes after setting the current, if the motor?s temperature rise too high, lower the setting current. if the output torque is inadequate after lower the current, improve the radiation condition to ensure that the motor and driver not burn hand. it?s better to let the driver work in breezy environment or fix it in metal board to improve the radiation.
|
